1. Hydrographic surveys deal with the mapping of
A. large water bodies
B. heavenly bodies
C. mountaineous region
D. canal system
E. movement of clouds.
Answer: A
3. An ideal vertical curve to join two gradients, is
A. circular
B. parabolic
C. elliptical
D. hyperbolic
E. none of these.
Answer: B
4. Pick up the correct statement from the following :
A. the eyepiece plays no part in defining the line of sight
B. the diaphragm plays no part in defining the line of sight
C. the optical centre of the objective plays no part in defining the line of sight
D. none of these.
Answer: A
5. The intercept of a staff
A. is maximum if the staff is held truly normal to the line of sight.
B. is minimum if the staff is held truly normal to the line of sight.
C. decreases if the staff is tilted away from normal
D. increases if the staff is tilted towards normal.
Answer: B
6. The radius of curvature of the arc of the bubble tube is generally kept
A. 10 m
B. 25 m
C. 50 m
D. 100 m
Answer: D
7. If S is the length of a subchord and R is the radius of simple curve, the angle of deflection between its tangent and sub-chord, in minutes, is equal to
A. 573 S/R
B. 573 R/S
C. 171.9 S/R
D. 1718.9 R/S
E. 1718.9 S/R.
Answer: E
8. The real image of an object formed by the objective, must lie
A. in the plane of cross hairs
B. at the centre of the telescope
C. at the optical centre of the eye-piece
D. anywhere inside the telescope.
Answer: A
9. In chain surveying tie lines are primarily provided
A. to check the accuracy of the survey
B. to take offsets for detail survey
C. to avoid long offsets from chain lines
D. to increase the number of chain lines.
Answer: C
10. Pick up the correct statement from the following :
A. the tangent screw enables to give small movement under conditions of smooth and positive control
B. standing on the tripod is the levelling head or trib arch
C. the levelling screws are used to tilt the instrument so that its rotation axis is truly vertical
D. all the above.
Answer: D
15. Closed contours of decreasing values towards their centre, represent
A. a hill
B. a depression
C. a saddle or pass
D. a river bed.
Answer: B
13. The accuracy of measurement in chain surveying, does not depend upon
A. length of the offset
B. scale of the plotting
C. importance of the features
D. general layout of the chain lines.
Answer: D
11. One of the Lehmann’s rules of plane tabling, is
A. location of the instrument station is always distant from each of the three rays from the known points in proportion to their distances
B. when looking in the direction of each of the given points, the instrument station will be on the right side of one and left side of the other ray
C. when the instrument station is outside the circumscribing circle its location is always on the opposite side of the ray to the most distant point as the inter-section of the other two rays
D. none of these.
Answer: A
17. Diopter is the power of a lens having a focal length of
A. 25 cm
B. 50 cm
C. 75 cm
D. 100 cm
E. 125 cm
Answer: D
18. An imaginary line joining the points of equal elevation on the surface of the earth, represents
A. contour surface
B. contour gradient
C. contour line
D. level line
E. none of these.
Answer: C
19. The ‘fix’ of a plane table station with three known points, is bad if the plane table station lies
A. in the great triangle
B. outside the great triangle
C. on the circumference of the circumscribing circle
D. none of these.
Answer: C
20. If R is the radius of the main curve, θ the angle of deflection, S the shift and L the length of the transition curve, then, total tangent length of the curve, is
A. (R – S) tan θ/2 – L/2
B. (R + S) tan θ/2 – L/2
C. (R + S) tan θ/2 + L/2
D. (R – S) tan θ/2 + L/2
E. (R – S) cos θ/2 + L/2
Answer: C
21. In chain surveying field work is limited to
A. linear measurements only
B. angular measurements only
C. both linear and angular measurements
D. all the above.
Answer: A
22. Two concave lenses of 60 cm focal length are cemented on either side of a convex lens of 15 cm focal length. The focal length of the combination is
A. 10 cm
B. 20 cm
C. 30 cm
D. 40 cm
Answer: C
23. One of the tacheometric constants is additive, the other constant, is
A. subtractive constant
B. multiplying constant
C. dividing constant
D. indicative constant.
Answer: B
24. The limiting length of an offset does not depend upon
A. accuracy of the work
B. method of setting out perpendiculars
C. scale of plotting
D. indefinite features to be surveyed.
Answer: D
25. Pick up the correct statement from the following:
A. the theodolite in which telescope can be rotated in vertical plane is called a transit
B. when the vertical circle is to the left of the telescope during observation, it is called to be in left face
C. when the vertical circle is to the right of the telescope during observation, it is called to be in right face
D. all the above.
Answer: D
26. Pick up the method of surveying in which field observations and plotting proceed simultaneously from the following
A. chain surveying
B. compass surveying
C. plan table surveying
D. tacheometric surveying.
Answer: C
27. While viewing through a level telescope and moving the eye slightly, a relative movement occurs between the image of the levelling staff and the cross hairs. The instrument is
A. correctly focussed
B. not correctly focussed
C. said to have parallax
D. free from parallax.
Answer: C
28. In quadrantal bearing system, back bearing of a line may be obtained from its forward bearing, by
A. adding 180°, if the given bearing is less than 180°
B. subtracting 180°, if the given bearing, is more than 180°
C. changing the cardinal points, i.e. substituting N for S and E for W and vice-versa
D. none of these.
Answer: C
29. Accuracy of ‘fix’ by two point problem, is
A. bad
B. good
C. not reliable
D. unique.
Answer: C
30. A bearing of a line is also known as
A. magnetic bearing
B. true bearing
C. azimuth
D. reduced bearing
Answer: B
31. True meridians are generally preferred to magnetic meridians because
A. these converge to a point
B. these change due to change in time
C. these remain constant.
D. None of these.
Answer: C
32. Pick up the correct statement from the following :
A. the apparent error on reversal is twice the actual error
B. the correction may be made equal to half the observed discrepancy.
C. the good results may be obtained from a defective instrument by reversing and taking the mean of two erroneous results
D. all the above.
Answer: D
33. The bearings of the lines AB and BC are 146° 30′ and 68° 30′. The included angle ABC is
A. 102°
B. 78°
C. 45°
D. none of these.
Answer: A
34. The most reliable method of plotting a theodolite traverse, is
A. by consecutive co-ordinates of each station
B. by independent co-ordinates of each station
C. by plotting included angles and scaling off each traverse leg
D. by the tangent method of plotting.
Answer: B
35. The difference of level between a point below the plane of sight and one above, is the sum of two staff readings and an error would be produced equal to
A. the distance between the zero of gradient and the foot of the staff
B. twice the distance between the zero of graduation and the foot of the staff
C. thrice the distance between the zero of graduation and the foot of the staff
D. none of the above.
Answer: B
36. Offsets are measured with an accuracy of 1 in 40. If the point on the paper from both sources of error (due to angular and measurement errors) is not to exceed 0.05 cm on a scale of 1 cm = 20 m, the maximum length of offset should be limited to
A. 14.14
B. 28.28 m
C. 200 m
D. none of these.
Answer: B
37. The bearings of the lines AB and BC are 146° 30′ and 68° 30′. The included angle ABC is
A. 102°
B. 78°
C. 45°
D. none of these.
Answer: A
38. For a closed traverse the omitted measurements may be calculated
A. length of one side only
B. bearing of one side only
C. both length and bearing of one side
D. length or bearing of adjacent side
E. all the above.
Answer: E
39. The slope correction for a length of 30 m along a gradient of 1 in 20, is
A. 3.75 cm
B. 0.375 cm
C. 37.5 cm
D. 2.75 cm.
Answer: A
40. The main principle of surveying is to work
A. from part to the whole
B. from whole to the part
C. from higher level to the lower level
D. from lower level to higher level.
Answer: B
41. For the construction of highway (or railway)
A. longitudinal sections are required
B. cross sections are required
C. both longitudinal and cross sections are required
D. none of these.
Answer: C
42. If the radius of a simple curve is R, the length of the chord for calculating offsets by the method of chords produced, should not exceed.
A. R/10
B. R/15
C. R/20
D. R/25.
Answer: C
43. The sensitiveness of a level tube decreases if
A. radius of curvature of its inner surface is increased
B. diameter of the tube is increased
C. length of the vapour bubble is increased
D. both viscosity and surface tension are increased.
Answer: D
44. For true difference in elevations between two points A and B, the level must be set up
A. at any point between A and B
B. at the exact mid point of A and B
C. near the point A
D. near the point B.
Answer: B
45. ABCD is a regular parallelogram plot of land whose angle BAD is 60°. If the bearing of the line AB is 30°, the bearing of CD, is
A. 90°
B. 120°
C. 210°
D. 270°
Answer: C
46. Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the sight on the down-slope, must be less than
A. 30 m
B. 25 m
C. 20 m
D. 15 m
Answer: B
47. Pick up the correct statement from the following :
A. Box sextant is used for the measurement of horizontal angles
B. Cross staff is used for setting out right angles
C. Gradiometer is used for setting out any required gradient
D. Line ranger is used for locating intermediate stations on a survey line
E. All the above.
Answer: E
48. An ideal transition curve is
A. cubic parabola
B. cubic spiral
C. clothoid spiral
D. true spiral.
Answer: C
49. Pantagraph is used for
A. measuring distances
B. measuring areas
C. enlarging or reducing plans
D. setting out right angles
Answer: C
50. If the angular measurements of a traverse are more precise than its linear measurements, balancing of the traverse, is done by
A. Bowditch’s rule
B. Transit rule
C. Empirical rule
D. all of the above.
Answer: B
51. The branch of surveying in which both horizontal and vertical positions of a point, are determined by making instrumental observations, is known
A. tacheometry
B. tachemetry
C. telemetry
D. all the above.
Answer: D
52. In levelling operation
A. when the instrument is being shifted, the staff must not be moved
B. when the staff is being carried forward, the instrument must remain stationary
C. both (a) and (b)
D. neither (a) nor (b).
Answer: C
53. If the rate of gain of radial acceleration is 0.3 m per sec3 and full centrifugal ratio is developed. On the curve the ratio of the length of the transition curve of same radius on road and railway, is
A. 2.828
B. 3.828
C. 1.828
D. 0.828.
Answer: A
54. The angle between two plane mirrors of optical square, is
A. 20°
B. 30°
C. 45°
D. 60°
E. 90°.
Answer: C
55. The latitude of a traverse leg is obtained by multiplying its length by
A. tangent of its reduced bearing
B. sign of its reduced bearing
C. cosine of its reduced bearing
D. cosecant of its reduced bearing.
Answer: C
56. For a curve of radius 100 m and normal chord 10 m, the Rankine’s deflection angle, is
A. 0°25′.95
B. 0°35′.95
C. 1°25′.53
D. 1°35′.95
E. 2°51′.53.
Answer: E
57. A uniform slope was measured by the method of stepping. If the difference in level between two points is 1.8 m and the slope distance between them is 15 m, the error is approximately equal to
A. cumulative, + 0.11 m
B. compensating, ± 0.11 m
C. cumulative, – 0.11 m
D. none of these
Answer: A
58. In optical reading instruments
A. the vertical circle is usually continuous from 0° to 359°
B. the readings increase when the telescope is elevated in the face left position
C. the readings decrease when the telescope is elevated in the face right position
D. all the above.
Answer: D
59. For setting out a simple curve, using two theodolites.
A. offsets from tangents are required
B. offsets from chord produced are required
C. offsets from long chord are required
D. deflection angles from Rankine’s formula are required
E. none of these.
Answer: E
60. Geodetic surveying is undertaken
A. for production of accurate maps of wide areas
B. for developing the science of geodesy
C. making use of most accurate instruments and methods of observation
D. for determination of accurate positions on the earth’s surface of system of control points
E. all the above.
Answer: E
61. The desired sensitivity of a bubble tube with 2 mm divisions is 30″. The radius of the bubble tube should be
A. 13.75 m
B. 3.44 m
C. 1375 m
D. none of these.
Answer: A
62. A dumpy level was set up at the midpoint between two pegs A and B, 50 m apart and the staff readings at A and B were 1.22 and 1.06. With the level set up a A, the readings at A and B were 1.55 and 1.37. The collimation error per 100 m length of sight is
A. 0.02 m inclined upwards
B. 0.04 m inclined downwards
C. 0.04 m inclined upward
D. none of these.
Answer: B
63. Pick up the correct statement from the following :
A. the length of the brass handle is included in the length of chain
B. the handles are on swivel joints to prevent twisting of the chain
C. the fifth tag from either end of the chain is numbered 5
D. the length of the Gunter’s chain is 66 ft.
E. all the above.
Answer: E
64. Two hill tops A and B 20 km apart are intervened by a third top C. If the top most contour of the three hill tops are of the same value, state whether the line of sight AB
A. passes clear of hill top C
B. passes below the hill top C
C. grazes the hill top C
D. none of these.
Answer: B
65. True meridian of different places
A. converge from the south pole to the north pole
B. converge from the north pole to the south pole
C. converge from the equator to the poles
D. run parallel to each other.
Answer: C
66. The diaphragm of a stadia theodolite is fitted with two additional
A. horizontal hairs
B. vertical hairs
C. horizontal and two vertical hairs
D. none of these.
Answer: A
67. Centering error of a theodolite produces an error
A. in all angles equally
B. which does not vary with the direction or pointing
C. which varies with the direction of pointing and inversely with the length of sight
D. none of these.
Answer: C
68. In levelling operation
A. if second reading is more than first, it represents a rise
B. if first reading is more than second, it represents a rise
C. if first reading is less than second, it represents a fall
D. if second reading is less than first, it represents a fall
E. both (b) and (c).
Answer: E
69. Pick up the correct statement from the following :
A. in astronomical telescope, the rays from the object after refraction at the objective are brought to a focus before entering the eyepiece to produce a real inverted image in front of the eye piece
B. in Galileo’s telescope, the rays from the object get refracted at the objective and are intercepted by the eyepiece before a real image is formed
C. a line passing through the optical centre of the objective traversing through the eyepiece, is called line of sight
D. the line of sight which passes through the intersection of cross-lines marked on a diaphragm fixed in front of the eyepiece in a plane at right-angles to the axis, is called the line of collimation
E. all the above.
Answer: E
70. The operation of making the algebraic sum of latitudes and departures of a closed traverse, each equal to zero, is known
A. balancing the sights
B. balancing the departures
C. balancing the latitudes
D. balancing the traverse.
Answer: D
71. Orientation of a plane table by solving two point problem is only adopted when
A. saving of time is a main factor
B. better accuracy is a main factor
C. given points are inaccessible
D. none of these.
Answer: C
72. A back sight
A. is always taken on a point of known elevation or can be computed
B. is added to the known level to obtain the instrument height
C. taken on an inverted staff is treated as negative
D. all the above.
Answer: D
73. The best method of interpolation of contours, is by
A. estimation
B. graphical means
C. computation
D. all of these.
Answer: C
74. Pick up the correct specification of Ramsden eyepiece from the following :
A. it consists of two equal piano convex lenses
B. the curved surfaces of plano-convex lenses face each other
C. the two lenses are separated by a distance equal to 2/3 of the focal length of either lens.
D. the distance between the diaphragm and the front lens of the eyepiece is kept equal to 1/4 th of the focal length of a lens so that rays from a point on the diaphragm enter the eye as a parallel beam
E. all the above.
Answer: E
75. The systematic errors which persist and have regular effects in the performance of a survey operation, are due to
A. carelessness
B. faulty instrument
C. inattention
D. none of these.
Answer: B
76. The sum of the interior angles of a geometrical figure laid on the surface of the earth differs from that of the corresponding plane figure only to the extent of one second for every
A. 100 sq. km of area
B. 150 sq. km of area
C. 200 sq. km of area
D. none of these.
Answer: C
77. Deviation of the actual road gradient from the proposed contou’r gradient up hill side, involves
A. embankment on the centre line
B. excavation on the centre line
C. earth work on the centre line
D. none of these.
Answer: B
78. Measuring with a 30 m chain, 0.01 m too short, introduces
A. positive compensating error
B. negative compensating error
C. positive cumulative error
D. negative cumulative error.
Answer: C
79. Setting out a curve by two theodolite method, involves
A. linear measurements only
B. angular measurements only
C. both linear and angular measurements
D. none of these.
Answer: B
80. When the bubble of the level tube of a level, remains central
A. line of sight is horizontal
B. axis of the telescope is horizontal
C. line of collimation is horizontal
D. geometrical axis of the telescope is horizontal.
Answer: A
81. The vertical angle between longitudinal axis of a freely suspended magnetic needle and a horizontal line at its pivot, is known
A. declination
B. azimuth
C. dip
D. bearing.
Answer: C
82. A relatively fixed point of known elevation above datum, is called
A. bench mark
B. datum point
C. reduced level
D. reference point.
Answer: A
83. Cross hairs in surveying telescopes, are fitted
A. in the objective glass
B. at the centre of the telescope
C. at the optical centre of the eye piece
D. in front of the eye piece.
Answer: D
84. Metric chains are generally available in
A. 10 m and 20 m length
B. 15 m and 20 m length
C. 20 m and 30 m length
D. 25 m and 100 m length
Answer: C
85. On a diagonal scale, it is possible to read up to
A. one dimension
B. two dimensions
C. three dimensions
D. four dimensions.
Answer: C
86. Plotting of inaccessible points on a plane table, is done by
A. intersection
B. traversing
C. radiation
D. none of these.
Answer: A
87. A dumpy level is set up with its eye-piece vertically over a peg A. The height from the top of peg A to the centre of the eye-piece is 1.540 m and the reading on peg B is 0.705 m. The level is then setup over B. The height of the eye-piece above peg B is 1.490 m and a reading on A is 2.195 m. The difference in level between A and B is
A. 2.900 m
B. 3.030 m
C. 0.770 m
D. 0.785 m
E. 1.770 m.
Answer: C
88. The curve composed of two arcs of different radii having their centres on the opposite side of the curve, is known
A. a simple curve
B. a compound curve
C. a reverse curve
D. a vertical curve.
Answer: C
89. The ratio of the angles subtended at the eye, by the virtual image and the object, is known as telescope’s
A. resolving power
B. brightness
C. field of view
D. magnification.
Answer: D
90. The bubble tube is nearly filled with
A. alcohol or chloroform
B. a liquid which is very mobile
C. a liquid having low freezing point
D. all the above.
Answer: D
91. Simpson’s rule for calculating areas states that the area enclosed by a curvilinear figure divided into an even number of strips of equal width, is equal to
A. half the width of a strip, multiplied by the sum of two extreme offsets, twice the sum of remaining odd offsets, and thrice the sum of the even offsets
B. one third the width of a strip, multiplied by the sum of two extreme offsets, twice the sum of remaining odd offsets and four times the sum of the even offsets
C. one third the width of a strip, multiplied by the sum of two extreme offsets, four times the sum of the remaining odd offsets, and twice the sum of the even offsets
D. one sixth the width of a strip, multiplied by the sum of the two extreme offsets, twice the sum of remaining odd offsets and four times the sum of the even offsets
E. none of these
Answer: B
92. In a constant level tube, size of the bubble remains constant because upper wall is
A. of relatively larger radius
B. of relatively smaller radius
C. flat
D. convex downwards.
Answer: A
93. Prismatic compass is considered more accurate than a surveyor’s compass, because
A. it is provided with a better magnetic needle
B. it is provided with a sliding glass in the object vane
C. its graduations are in whole circle bearings
D. it is provided with a prism to facilitate reading of its graduated circle
E. both (c) and (d).
Answer: D
94.In reciprocal levelling, the error which is not completely eliminated, is due to
A. earth’s curvature
B. non-adjustment of line of collimation
C. refraction
D. non-adjustment of the bubble tube.
Answer: C
95. In tacheometrical observations, vertical staff holding is generally preferred to normal staffing, due to
A. ease of reduction of observations
B. facility of holding
C. minimum effect of careless holding on the result
D. none of these.
Answer: C
96. Removal of parallax, may be achieved by focussing
A. the objective
B. the eye-piece
C. the objective and the eye-piece
D. none of these.
Answer: C
97. Pick up the correct statement from the following :
A. A level surface is perpendicular at all points to the direction of gravity
B. A level line lies in level surface
C. A horizontal surface is normal to the direction of gravity at only one point
D. A horizontal line is tangential to the level surface
E. All the above.
Answer: E
98. The direction of steepest slope on a contour, is
A. along the contour
B. at an angle of 45° to the contour
C. at right angles to the contour
D. none of these.
Answer: C
99. Back bearing of a line is equal to
A. Fore bearing ± 90°
B. Fore bearing ± 180°
C. Fore bearing ± 360°
D. Fore bearing ± 270°
Answer: B
100. In an internal focusing telescope
A. the objective is at a fixed distance from the diaphragm
B. the focusing is done by the sliding of a divergent lens.
C. the focusing divergent lens is situated at about the middle of the tube
D. all the above.
Answer: D
101. The longitudinal section of the surface of bubble tube is
A. straight
B. circular
C. parabolic
D. elliptic.
Answer: B
102. Imaginary line passing through points having equal magnetic declination is termed as
A. isogon
B. agonic line
C. isoclinic line
D. none of these.
Answer: A
103. While rotating the theodolite in the horizontal plane, the bubble of the bubble tube takes up the same position in its tube, it indicates
A. the rotation axis is vertical
B. the trummion axis is horizontal
C. the line of collimation is perpendicular to vertical axis
D. none of the above
Answer: A
104. The main plate of a transit is divided into 1080 equal divisions. 60 divisions of the vernier coincide exactly with 59 divisions of the main plate. The transit can read angles accurate upto
A. 5″
B. 10″
C. 15″
D. 20″
E. 30″
Answer: D
105. Pick up the correct statement from the following :
A. the lines of sight while observing back sight and fore sight lie in the same horizontal plane
B. the staff readings are measurements made vertically downwards from a horizontal plane
C. the horizontal plane with reference to which staff readings are taken, coincides with the level surface through the telescope axis
D. all the above.
Answer: D
106. A traverse deflection angle is
A. less than 90°
B. more than 90° but less than 180°
C. the difference between the included angle and 180°
D. the difference between 360° and the included angle.
Answer: C
107. While measuring a chain line between two stations A and B intervened by a raised ground
A. vision gets obstructed
B. chaining gets obstructed
C. both vision and chaining get obstructed
D. all the above.
Answer: A
108 The Random errors tend to accumulate proportionally to
A. numbers of operations involved
B. reciprocal of operations involved
C. square root of the number of operation involved
D. cube root of the number of operation involved.
Answer: C
109. The true meridian of a place is the line in which earth’s surface is intersected by a plane through
A. east and west points
B. zenith and nadir points
C. north and south geographical poles
D. north and south magnetic poles.
Answer: C
110. The least count of a vernier scale is
A. sum of the smallest divisions of main and vernier scales
B. value of one division of the primary scale divided by total number of divisions of vernier scale
C. value of one division of vernier scale divided by total number of divisions of primary scale
D. none of these.
Answer: B
111. Which one of the following procedures for getting accurate orientation is the most distinctive feature of the art of plane tabling
A. radiation
B. intersection
C. traversing
D. resection.
Answer: D
112. A clinometer is used for
A. measuring angle of slope
B. correcting line of collimation
C. setting out right angles
D. defining natural features.
Answer: A
113. Diurnal variation of magnetic declination is
A. greater at equator than nearer the poles
B. less at equator than nearer the poles
C. less in summer than in winter
D. same at all latitudes and during different months.
Answer: B
114. The ‘fix’ of a plane table from three known points, is good, if
A. middle station is nearest
B. middle station is farthest
C. either the right or left station is nearest
D. none of these.
Answer: A
115. The construction of optical square is based, on the principle of optical
A. reflection
B. refraction
C. double refraction
D. double reflection.
Answer: D
116. If the smallest division of a vernier is longer than the smallest division of its primary scale, the vernier is known as
A. direct vernier
B. double vernier
C. retrograde vernier
D. simple vernier.
Answer: C
117. Cross-staff is used for
A. setting out right angles
B. measuring contour gradient
C. taking levels
D. measuring distances
E. none of these
Answer: A
118. The ‘point of curve’ of a simple circular curve, is
A. point of tangency
B. point of commencement
C. point of intersection
D. mid-point of the curve
Answer: B
119. For orientation of a plane table with three points A, B and C, Bessel’s drill is
A. Align b through a and draw a ray towards c, align a through b and draw a ray towards c, finally align c through the point of intersection of the previously drawn rays
B. Align c through a and draw a ray towards b, align a through c and draw a ray towards b, finally align b through the point of intersection of the previously drawn rays
C. Align c through b and draw a ray towards a, align b through c and draw a ray towards a, finally align a, through the point of intersection of the previously, drawn rays
D. In the first two steps any two of the points may be used and a ray drawn towards the third point, which is sighted through the point of intersection of previously drawn rays in the final step.
Answer: D
120. The minimum range for sliding the focusing lens in the internal focusing telescope for focusing at all distances beyond 4 m is
A. 5 mm
B. 10 mm
C. 15 mm
D. 20 mm.
Answer: D
121. Ramsden eye-piece consists of
A. two convex lenses short distance apart
B. two concave lenses short distance apart
C. one convex lens and one concave lens short distance apart
D. two plano-convex lenses short distance apart, with the convex surfaces facing each other.
Answer: D
122. The distance between steps for measuring down hill to obtain better accuracy
A. decreases with decrease of slope
B. increases with increase of slope
C. decreases with increase of slope
D. decreases with decrease of weight of the chain.
Answer: C
123. The tangent to the liquid surface in a level tube, is parallel to the axis of the level tube at
A. every point of the bubble
B. either end of the bubble
C. the mid-point of the bubble
D. no where.
Answer: C
124. Pick up the correct statement from the following :
A. in the earth’s magnetic field, a magnetic needle rests in magnetic meridian
B. the angle between the true meridian and the magnetic meridian is called magnetic variation
C. one end of the magnetic needle supported at its centre of gravity tends to dip down towards the. nearer magnetic pole of the earth
D. the magnet properly pivoted is balanced by means of riding weight movable along the needle
E. all the above.
Answer: E
125. Pick up the correct statement from the following :
A. If the slope of the curve of a mass diagram in the direction of increasing abscissa is downward, it indicates an embankment
B. The vertical distance between a maximum ordinate and the next forward maximum ordinate represents the whole volume of the embankment
C. The vertical distance between a minimum ordinate and the next forward maximum ordinate represents the whole volume of a cutting
D. The area enclosed by a loop of the curve and balancing line, measures the haul in that direction.
E. all the above.
Answer: E
126. Pick up the correct statement from the following :
A. if the image of the object does not fall on the plane of the cross-lines, parallax exists
B. parallax has nothing to do with the eyepiece
C. the eyepiece is adjusted for clear vision of the cross hairs
D. all the above.
Answer: D
127. The slope correction may be ignored if
A. the slope of the ground is less than 3°
B. to slope of the ground is say 1 in 19
C. both (a) and (b)
D. neither (a) nor (b)
Answer: C
128. If a tacheometer is fitted with an anal-latic lens
A. additive constant is 100, multiplying constant is zero
B. multiplying constant is 100, additive constant is zero
C. both multiplying and additive constants are 100
D. both multiplying and additive constants are 50.
Answer: B
129. Volume of the earth work may be calculated by
A. mean areas
B. end areas
C. Prismoidal formula
D. Trapezoidal
E. all the above.
Answer: E
130. Which one of the following mistakes/errors may be cumulative + or – :
A. bad ranging
B. bad straightening
C. erroneous length of chain
D. sag.
Answer: C
131. The orthographical projection of a traverse leg upon the reference meridian, is known as
A. departure of leg
B. latitude to the leg
C. co-ordinate of the leg
D. bearing of the leg.
Answer: B
132. The whole circle bearing of a line is 290°. Its reduced bearing is
A. N 20° E
B. N 20° W
C. N 70° W
D. S 70° E
Answer: C
133. Which of the following introduces an error of about 1 in 1000 if 20 m chain is used
A. length of chain 20 mm wrong
B. one end of the chain 0.9 m off the line
C. one end of chain 0.9 m higher than the other
D. middle of the chain 0.45 m off the line
E. all the above.
Answer: E
134. The reduced bearing of a line is N 87° W. Its whole circle bearing is
A. 87°
B. 273°
C. 93°
D. 3°
Answer: B
135. Surveys which are carried out to depict mountains, rivers, water bodies, wooded areas and other cultural details, are known as
A. cadastral surveys
B. city surveys
C. topographical surveys
D. guide map surveys
E. plane surveys.
Answer: C
136. The total change in level along the line is equal to total back sights
A. minus total fore sights
B. the total rises minus total falls
C. the reduced level of last point minus reduced level of the first point
D. all the above.
Answer: D
137. ABCD is a rectangular plot of land. If the bearing of the side AB is 75°, the bearing of DC is
A. 75°
B. 255°
C. 105°
D. 285°
Answer: A
138. Grid lines are parallel to
A. magnetic meridian of the central point of the grid
B. line representing the central true meridian of the grid
C. geographical equator
D. none of these.
Answer: B
139. Total latitude of a point is positive if it lies
A. north of the reference parallel
B. south of the reference parallel
C. east of the reference parallel
D. west of the reference parallel.
Answer: A
140. In levelling operation,
A. The first sight on any change point is a back sight
B. The second sight on any change point is a fore sight
C. The line commences with a fore sight and closes with a back sight
D. The line commences with a back sight and closes with a foresight.
Answer: D
141. The apparent error on reversal is
A. equal to the actual error
B. twice the actual error
C. thrice the actual error
D. none of these.
Answer: B
142. Magnetic declination at any place
A. remains constant
B. does not remain constant
C. fluctuates
D. changes abruptly.
Answer: B
143. Systematic errors are those errors
A. which cannot be recognised
B. whose character is understood
C. whose effects are cumulative and can be eliminated
D. none of these.
Answer: C
144. An angle of deflection right, may be directly obtained by setting the instrument to read
A. zero on back station
B. 180° on back station
C. 90°
D. 270° on back station.
Answer: A
145. The method of finding out the difference in elevation between two points for eliminating the effect of curvature and refraction, is
A. reciprocal levelling
B. precise levelling
C. differential levelling
D. flying levelling
Answer: A
146. Transition curves are introduced at either end of a circular curve, to obtain
A. gradually decrease of curvature from zero at the tangent point to the specified quantity at the junction of the transition curve with main curve
B. gradual increase of super-elevation from zero at the tangent point to the specified amount at the junction of the transition curve with main curve
C. gradual change of gradient from zero at the tangent point to the specified amount at the junction of the transition curve with main curve
D. none of these.
Answer: B
147. The horizontal angle between true meridian and magnetic meridian, is known
A. bearing
B. magnetic declination
C. dip
D. convergence.
Answer: B
148. With usual notations, the expression represents
A. centrifugal force
B. centrifugal ratio
C. super elevation
D. radial acceleration.
Answer: B
149. Accuracy of elevation of various points obtained from contour map is limited to
A. of the contour interval
B. th of the contour interval
C. rd of the contour interval
D. th of the contour interval.
Answer: A
150. Magnetic bearing of a survey line at any place
A. remains constant
B. changes systematically
C. varies differently in different months of the year
D. is always greater than true bearing.
Answer: C
151. Perpendicularity of an offset may be judged by eye, if the length of the offset is
A. 5 m
B. 10 m
C. 15 m
D. 20 m.
Answer: C
152. The bearings of two traverse legs AB and BC are N52° 45′ E and N34° 30′ E respectively. The deflection angle is
A. 18° 15′ E
B. 18° 15′ N
C. 18° 15′ W
D. 18° 15′ R
E. 18° 15′ L
Answer: E
153. A lemniscate curve will not be transitional throughout, if its deflection angle, is
A. 45°
B. 60°
C. 90°
D. 120°
E. 180°
Answer: A
154. Ranging in chain survey means
A. looking at an isolated point not on the line
B. establishing an intermediate point on the line
C. determining the distance between end points
D. determining the offset distance
E. none of these
Answer: B
155. Accurate measurement of deflection angles with a transit not properly adjusted may be made by
A. setting the vernier A at zero at back station and then plunging the telescope
B. setting the vernier A at zero at back station and turning the instrument to the forward station
C. taking two back sights one with the telescope normal and the other with telescope inverted
D. none of these.
Answer: C
156. If whole circle bearing of a line is 120°, its reduced bearing is
A. S 20° E
B. S 60° E
C. N 120° E
D. N 60° E.
Answer: B
157. In a lemniscate curve the ratio of the angle between the tangent at the end of the polar ray and the straight, and the angle between the polar ray and the straight, is
A. 2
B. 3
C. 4
D. 5
E. 3/2
Answer: E
158. Greater accuracy in linear measurements, is obtained by
A. tacheometry
B. direct chaining
C. direct taping
D. all the above.
Answer: C
159. From any point on the surface with a given inclination
A. only one contour gradient is possible
B. two contour gradients are possible
C. indefinite contour gradients are possible
D. all the above.
Answer: C
160. Angles to a given pivot station observed from a number of traverse stations when plotted, the lines to the pivot station intersect at a common point
A. angular measurements are correct and not the linear measurements
B. linear measurements are correct and not the angular measurements
C. angular and linear measurements are correct and not the plotting of traverse
D. angular and linear measurements and also plotting of the traverse are correct.
Answer: D
161. Reduced bearing of a line is an angle between
A. north line and given line measured clockwise
B. north line and given line measured anticlockwise
C. east or west and the given line
D. given line and the part of the meridian whether N end or S end, lying adjacent to it.
Answer: D
162. While measuring with a metallic tape of 30 m length pull should be applied
A. 1 kg
B. 2 kg
C. 3 kg
D. 4 kg
Answer: C
163. The ratio of the linear displacement at the end of a line, subtended by an arc of one second to the length of the line, is
A. 1:206 300
B. 1:3440
C. 1:57
D. 1:100.
Answer: A
164. The co-ordinate of a point measured perpendicular to the parallel, is called
A. total latitude
B. meridian distance
C. total departure
D. consecutive co-ordinate.
Answer: A
165. The magnetic meridian at any point, is the direction indicated by a freely suspended
A. magnetic needle
B. and properly balanced magnetic needle
C. properly balanced and uninfluenced by local attractive force
D. magnetic needle over an iron pivot.
Answer: C
166. If the radius of a simple curve is 600 m, the maximum length of the chord for calculating offsets, is taken
A. 10 m
B. 15 m
C. 20 m
D. 25 m
E. 30 m.
Answer: E
167. For preparation of a contour plan for a route survey
A. method of squares is used
B. method of trace contour is used
C. method of cross profile is used
D. indirect method of contouring is used.
Answer: C
168. Flint glass
A. has slightly the greater refracting power than crown glass
B. has roughly double refracting power than that of crown
C. and crown glass proportions yield the required focal length and neutralise the dispersion produced by the convex lens at the emergence from the concave
D. all the above.
Answer: D
169. The zero of the graduated circle of a prismatic compass is located at
A. north end
B. east end
C. south end
D. west end.
Answer: C
170. The bearing of AB is 190° and that of CB is 260° 30′. The included angle ABC, is
A. 80° 30′
B. 99° 30′
C. 70° 30′
D. none of these
Answer: C
171. The power of a lens
A. is reciprocal of its focal length
B. is positive if it is a convex lens
C. is negative if it is a concave lens
D. is measured in diopter.
Answer: D
172. In an adjusted level, when the bubble is central, the axis of the bubble tube becomes parallel to
A. line of sight
B. line of collimation
C. axis of the telescope
D. None of these.
Answer: A
173. The ratio of the distances at which a stated length can be distinguished by the telescope and the human eye, respectively, is called
A. brightness of telescope
B. magnification of telescope
C. resolving power of telescope
D. none of these.
Answer: C
174. Bergchrund is a topograhical feature in
A. plains
B. water bodies
C. hills
D. glaciated region
Answer: D
175. To orient a plane table at a point P roughly south of the mid-point of two inaccessible conical hill stations A and B in the plains, a point C is selected in line with AB and table is oriented at C by bringing ab in line with AB. A ray is then drawn towards P and at P the table is oriented by back ray method. The orientation so obtained, is
A. unique and correct
B. incorrect
C. manifold and correct
D. not reliable.
Answer: C
176. Which one of the following statements is correct ?
A. when the axes of rotation of the graduated circle and the verniers are not coincident, the instrument possesses eccentricity
B. the mean of the readings of the two verniers gives correct reading free from the eccentricity
C. one vernier may be used if the readings of two verniers differ by a constant
D. all the above.
Answer: D
177. Pick up the correct statement from the following
A. 1 second of arc corresponds to a displacement ratio of 1:206, 300
B. 1 degree of arc corresponds to a displacement ratio of 1:57
C. the angular errors tend to propagate themselves along a traverse as the square root of the number of stations
D. the errors arising from the linear measures tend to be roughly proportional to the lengths of the lines
E. all the above.
Answer: E
178. The chaining on sloping ground is
A. easier along the falling gradient
B. easier along the up gradient
C. equally convenient along falling as well as up gradient
D. all the above.
Answer: A
179. Profile levelling is usually done for determining
A. contours of an area
B. capacity of a reservoir
C. elevations along a straight line
D. boundaries of property
Answer: C
180. For indirect ranging, number of ranging rods required, is
A. 1
B. 2
C. 3
D. 4
E. 5
Answer: D
181. To avoid large centering error with very short legs, observations are generally made
A. to chain pins
B. by using optical system for centering the theodolite
C. to a target fixed on theodolite tripod on which theodolite may be fitted easily
D. all the above.
Answer: C
182. During secular variation of magnetic meridian at different places
A. range of oscillations is constant
B. period of oscillation is constant
C. range and period of oscillation both vary
D. period of oscillation only varies.
Answer: C
183. Designation of a curve is made by :
A. angle subtended by a chord of any length
B. angle subtended by an arc of specified length
C. radius of the curve
D. curvature of the curve.
Answer: C
184. The operation of resection involves the following steps
rough orientation of the plane table the three lines form a triangle of error drawing lines back through the three control points select a point in the triangle of error such that each ray is equally rotated either clockwise or anti clockwise the points obtained by three rays is the correct location.
The correct sequence is
A. 1, 3, 2, 4, 5
B. 1, 2, 3, 4, 5
C. 1, 4, 3, 2, 5
D. 1, 4, 2, 3, 5
Answer: A
185. The line of collimation method of reduction of levels, does not provide a check on
A. intermediate sights
B. fore sights
C. back sights
D. reduced levels.
Answer: A
186. If a linear traverse follows a sharp curve round a large lake where it is difficult to have long legs, the accuracy of the traverse may be improved by
A. taking short legs
B. making repeated observations of angular and linear measurements
C. making a subsidiary traverse to determine the length of a long leg
D. all the above.
Answer: C
187. Perpendicular offset from a tangent to the junction of a transition curve and circular curve is equal to
A. shift
B. twice the shift
C. thrice the shift
D. four times the shift.
Answer: D
188. Rankine’s deflection angle in minutes is obtained by multiplying the length of the chord by
A. degree of the curve
B. square of the degree of the curve
C. inverse of the degree of the curve
D. none of these.
Answer: A
190. The method of reversal
A. is usually directed to examine whether a certain part is truly parallel or perpendicular to another
B. makes the erroneous relationship between parts evident
C. both (a) and (b)
D. neither (a) nor (b).
Answer: C
191. You have to observe an included angle with better accuracy than what is achievable by a vernier, you will prefer the method of
A. repetition
B. reiteration
C. double observations
D. exactness.
Answer: A
192. If the plane table is not horizontal in a direction at right angles to the alidade, the line of sight is parallel to the fiducial edge only for
A. horizontal sights
B. inclined sights upward
C. inclined sight downward
D. none of these.
Answer: A
193. If the whole circle bearing of a line is 180°, its reduced bearing is
A. S 0° E
B. S 0° W
C. S
D. N.
Answer: C
194. The chord of a curve less than peg interval, is known as
A. small chord
B. sub-chord
C. normal chord
D. short chord.
Answer: B
195. Mistakes which may produce a very serious effect upon the final results arise due to
A. in attention
B. in experience
C. carelessness
D. all of these.
Answer: D
196. A well conditioned triangle has no angle less than
A. 20°
B. 30°
C. 45°
D. 60°.
Answer: B
197. Contour lines of different elevations can unite to form one line, only in the case of
A. a vertical cliff
B. a saddle
C. a water shed line
D. a hill top.
Answer: A
198. The line of sight is kept as high above ground surface as possible to minimise the error in the observed angles due to
A. shimmering
B. horizontal refraction
C. vertical refraction
D. both shimmering and horizontal refraction.
Answer: D
199. The distance between terminal points computed from a subsidiary traverse run between them, is generally known, as
A. traverse leg
B. a base
C. traverse base
D. all the above.
Answer: C
200. For locating a distant object visible from two transit stations, the method usually preferred to, is
A. Angles and distances from transit stations
B. Angles from two transit stations
C. distance from two transit stations
D. Angle from one transit station and distance from the other.
Answer: B
201. The smaller horizontal angle between the true meridian and a survey line, is known
A. declination
B. bearing
C. azimuth
D. dip.
Answer: C
202. Pick up the wrong statement from the following :
A. the diaphragm is placed between the eyepiece and the objective but nearer to the former
B. the diaphragm is placed between the eyepiece and the objective but nearer to the later
C. the outer component of the objective is a double-convex lens of crown glass
D. the inner component of the objective is a flint glass, convexo-concave
E. all the above.
Answer: B
203. Prolongation of chain line across an obstruction in chain surveying, is done by
A. making angular measurements
B. drawing perpendiculars with a chain
C. solution of triangles
D. all the above.
Answer: B
204. Check lines (or proof lines) in Chain Surveying, are essentially required
A. to plot the chain lines
B. to plot the offsets
C. to indicate the accuracy of the survey work
D. to increase the out-turn
Answer: C
205. Number of subdivisions per metre length of a levelling staff is
A. 100
B. 200
C. 500
D. 1000
Answer: B
206. The first reading from a level station is
A. foresight
B. intermediate sight
C. back-sight
D. any sight.
Answer: C
207. If the length of a transition curve to be introduced between a straight and a circular curve of radius 500 m is 90 m, the maximum deflection angle to locate its junction point, is
A. 1°43′ 08″
B. 1°43′ 18″
C. 1°43′ 28″
D. 1°43′ 38″
Answer: C
208. The length of a traverse leg may be obtained by multiplying the latitude and
A. secant of its reduced bearing
B. sine of its reduced bearing
C. cosine of its reduced bearing
D. tangent of its reduced bearing.
Answer: A
209. Pick up the correct statement from the following :
A. a refracting telescope consists optically of two lenses
B. the principal axes of both the lenses coincide the optical axis of the telescope
C. the lens nearer the object to be viewed is convex and is called objective
D. the lens nearer the eye is called eyepiece
E. all the above.
Answer: E
210. In chain surveying, perpendiculars to the chain line, are set out by
A. a theodolite
B. a prismatic compass
C. a level
D. an optical square
Answer: D
211. The difference in the lengths of an arc and its subtended chord on the earth surface for a distance of 18.2 km, is only
A. 1 cm
B. 5 cm
C. 10 cm
D. 100 cm.
Answer: C
212. The boundary of water of a still lake, represents
A. level surface
B. horizontal surface
C. contour line
D. a concave surface.
Answer: C
213. Diaphragm of a surveying telescope is held inside
A. eye-piece
B. objective
C. telescope tube at its mid point
D. telescope at the end nearer the eye-piece
E. telescope at its end nearer the objective.
Answer: D
214. The sag of 50 m tape weighing 4 kg under 5 kg tension is roughly
A. 0.043 m
B. 0.053 m
C. 0.063 m
D. 0.073 m
E. 0.083 m
Answer: E
215. If vertical angles of inclined sights do not exceed 10° and non-verticality of the staff remains within 1°, stadia system of tacheometric observations are made on
A. staff normal
B. staff vertical
C. staff normal as well as vertical
D. none of these.
Answer: A
216. While surveying a plot of land by plane tabling, the field observations
A. and plotting proceed simultaneously
B. and plotting do not proceed simultaneously
C. and recorded in field books to be plotted later
D. all the above.
Answer: A
217. The curvature of the earth’s surface, is taken into account only if the extent of survey is more than
A. 100 sq km
B. 160 sq km
C. 200 sq km
D. 260 sq km.
Answer: D
218. The area of any irregular figure of the plotted map is measured with
A. pentagraph
B. sextant
C. clinometer
D. planimeter
E. optical square
Answer: D
219. The angle of intersection of a contour and a ridge line, is
A. 30°
B. 45°
C. 60°
D. 90°.
Answer: D
220. In horizontal angles, the error due to imperfect levelling of the plate bubble is
A. large when sights are nearly level
B. large for long sights
C. less for steeply inclined sights
D. large for steeply inclined sights.
Answer: D
221. Pick up the correct statement from the following :
A. to locate a gross error in bearing that may exist in controlled theodolite traverse, we may plot the traverse from each end. The traverse station having the same coordinates by each route is the one where the error lies
B. to locate a gross error in bearing, in a controlled traverse, we plot the traverse and the station through which perpendicular to sector of the closing line passes is the station at which the error was made
C. to locate a gross error due to taping in a controlled traverse, we plot the traverse to a convenient scale. The bearing of the closing error will be approximately the same as that of the leg in which the gross error consists
D. all the above.
Answer: D
222. Pick up the correct statement from the following :
A. The horizontal angle between magnetic meridian and true meridian at a place is called magnetic declination or variance of the compass
B. the imaginary lines which pass through points at which the magnetic declinations are equal at a given time are called isogonic lines
C. the isogonic lines through places at which the declination is zero are termed agonic lines
D. all the above.
Answer: D
223. The distances AC and BC are measured from two fixed points A and B whose distance AB is known. The point C is plotted by intersection. This method is generally adopted in
A. chain surveying
B. traverse method of surveys
C. triangulation
D. none of these.
Answer: A
224. The slope correction for a 3° slope for a length of 100 m, is
A. -0.11 m
B. -0.12 m
C. -1.87 m
D. -0.137 m
Answer: D
225. Number of links per metre length of a chain are
A. 2
B. 5
C. 8
D. 10
E. 20
Answer: B
226. To orient a plane table at a point with two inaccessible points, the method generally adopted, is
A. intersection
B. resection
C. radiation
D. two point problem.
Answer: D
227. Tilt of the staff in stadia tacheometry increases the intercept if it is
A. away from the telescope pointing down hill
B. towards the telescope pointing up-hill
C. away from the telescope pointing up-hill
D. none of these.
Answer: C
228. The method generally preferred to for contouring an undulating area, is
A. chain surveying
B. plane table surveying
C. tacheometrical surveying
D. compass surveying.
Answer: C
229. If the declination of the needle is 10° W
A. each of the whole circle reckoning has to be micros by 10°
B. in the quadrantal method, the correction is positive in the 1st and 3rd quadrants
C. in the quadrantal method, the corrections is negative in 2nd and 4th quadrants
D. all the above.
Answer: D
230. A level when set up 25 m from peg A and 50 m from peg B reads 2.847 on a staff held on A and 3.462 on a staff held on B, keeping bubble at its centre while reading. If the reduced levels of A and B are 283.665 m and 284.295 m respectively, the collimation error per 100 m is
A. 0.015 m
B. 0.030 m
C. 0.045 m
D. 0.060 m
Answer: D
231. For taking offsets with an optical square on the right hand side of the chain line, it is held
A. by right hand upside down
B. by left hand upright
C. by right hand upright
D. by left hand up side down.
232. If the whole circle bearing of a line is 270°, its reduced bearing is
A. N 90° W
B. S 90° W
C. W 90°
D. 90° W.
Answer: C
233. Straight, parallel and widely spaced contours represent
A. a steep surface
B. a flat surface
C. an inclined plane surface
D. curved surface.
Answer: C
234. The theodolites used for making tacheometric observations by optical wedge system, are
A. provided with stadia hairs in front of eye piece
B. not provided with stadia hairs at all
C. fitted with a glass wedge inside the telescope
D. fitted with a glass wedge in front of telescope.
Answer: D
235. A lens or combination of lenses in which the following defect is completely eliminated is called aplanatic
A. spherical aberration
B. chromatic aberration
C. coma
D. astigmatism.
Answer: A
236. While setting a plane table at a station it was found that the error in centering was 30 cm away from the ray of length 40 m drawn from the station. If the scale of the plan is 1 cm = 2 cm, the displacement of the end of the ray in plan from the true position will be
A. 0.02 cm
B. 0.15 cm
C. 02 cm
D. 0.1 cm
Answer: B
237. Pick up the correct statement from the following :
A. with both handles in his left hand, the chain man throws out the chain with his right hand and the second chain man assists him to free it from knots
B. the follower of the chaining operation should be more experienced than the leader
C. at the end of the tenth chain length, the two chain men meet and the ten arrows are handed over to the leader
D. all the above.
Answer: D
238. Resolving power of a telescope depends on
A. the diameter of the aperture
B. the pupil aperture of the eye
C. the diameter of the object glass
D. all the above.
Answer: D
239. Staff readings on pegs x and y from X station are 1.755 m and 2.850 m, and from station Y on staff head at Y and X are 0.655 m and 1.560 m. If reduced level of X is 105.5 m, the reduced level of Y is
A. 104.0 m
B. 104.5 m
C. 105.0 m
D. 105.5 m
Answer: B
240. The constant vertical distance between two adjacent contours, is called
A. horizontal interval
B. horizontal equivalent
C. vertical equivalent
D. contour interval
E. contour gradient.
Answer: D
241. The reduced level of a floor is 99.995 m, the staff reading on the floor is 1.505 m. If the inverted staff reading against the roof is 1.795 m, the floor level below the slab, is
A. 3.290 m
B. 3.300 m
C. 3.275 m
D. 2.790 m
Answer: B
242. The correction to be applied to each 30 metre chain length along θ° slope, is
A. 30 (sec θ – 1) m
B. 30 (sin θ – 1) m
C. 30 (cos θ – 1) m
D. 30 (tan θ – 1) m
E. 30 (cot θ – 1) m.
Answer: A
243. Under ordinary conditions, the precision of a theodolite traverse is affected by
A. systematic angular errors
B. accidental linear errors
C. systematic linear errors
D. accidental angular errors.
Answer: C
244. Pick up the incorrect statement from the following :
A. while measuring a distance with a tape of length 100.005 m, the distance to be increasing by 0.005 m for each tape length
B. an increase in temperature causes a tape to increase in length and the measured distance is too large
C. the straight distance between end points of a suspended tape is reduced by an amount called the sag correction
D. a 100 m tape of cross section 10 mm x 0.25 mm stretches about 10 mm under 5 kg pull.
Answer: B
245. Stadia techeometry was discovered by James Watt in the year.
A. 1670
B. 1770
C. 1870
D. 1900.
Answer: B
246. The bearing of lines OA and OB are 16° 10′ and 332° 18′, the value of the included angle BOA is
A. 316° 10′
B. 158° 28′
C. 348° 08′
D. 43° 52′
Answer: D
247. The properties of autogenous curve for automobiles are given by
A. true spiral
B. cubic parabola
C. Bernoulli’s Lemniscate
D. clothoid spiral.
Answer: C
248. In a telescope the object glass of focal length 14 cm, is located at 20 cm from the diaphragm. The focussing lens is midway between them when a staff 16.50 m away is focussed. The focal length of the focussing lens, is
A. 5.24 cm
B. 6.24 cm
C. 7.24 cm
D. 8.24 cm
Answer: C
249. If + 0.8% grade meets – 0.7% grade and the rate of change of grade for 30 m distance is 0.05, the length of the vertical curve will be
A. 600 m
B. 700 m
C. 800 m
D. 900 m
E. 1000 m
Answer: D
250. The included angles of a theodolite traverse, are generally measured
A. clockwise from the forward station
B. anti-clockwise from the back station
C. anti-clockwise from the forward station
D. clockwise from the back station.
Answer: D
251. Location of contour gradient for a high way is best set out from
A. ridge down the hill
B. saddle down the hill
C. bottom to the ridge
D. bottom to the saddle.
Answer: B
252. The line normal to the plumb line is known as
A. horizontal line
B. level line
C. datum line
D. vertical line.
Answer: B
253. The angle of intersection of a curve is the angle between
A. back tangent and forward tangent
B. prolongation of back tangent and forward tangent
C. forward tangent and long chord
D. back tangent and long chord.
Answer: A
254. Planimeter is used for measuring
A. volume
B. area
C. contour gradient
D. slope angle
E. none of these
Answer: B
255. In a perfect prismatic compass
A. magnetic axis and geometric axis of the needle coincide
B. ends of the needle and pivot are in same vertical and horizontal planes
C. pivot is vertically over the centre of the graduated circle
D. needle is always kept sensitive
E. all the above.
Answer: E
256. The defect of a lens whereby rays of white light proceeding from a point get dispersed into their components and conveyed to various foci, forming a blurred and coloured image is known as
A. chromatic aberration
B. spherical aberration
C. astigmatism
D. coma.
Answer: A
257. The staff reading at a distance of 80 m from a level with the bubble at its centre is 1.31 m. When the bubble is moved by 5 divisions out of the centre, the reading is 1.39 m. The angular value of the one division of the bubble, is
A. 28.8 secs
B. 41.25 secs
C. 14.52 secs
D. 25.05
E. none of these
Answer: B
258. If i is the stadia distance, f is the focal length and d is the distance between the objective and vertical axis of the techeometer, the multiplying constant, is
A. f/i
B. i/f
C. (f + d)
D. f/d.
Answer: A
259. The back staff reading on a B.M. of R.L. 500.000 m is 2.685 m. If foresight reading on a point is 1.345 m, the reduced level of the point, is
A. 502.685 m
B. 501.345 m
C. 501.340 m
D. 504.030 m
E. 502.585 m.
Answer: C
260. It is more difficult to obtain good results while measuringhorizontal distance by stepping
A. up-hill
B. down-hill
C. in low undulations
D. in plane areas.
Answer: A
261. The additional lines which are measured to show the correctness of the chain surveying are called:
A. check clines
B. proof lines
C. tie lines
D. all of these.
Answer: D
262. The staff reading at a distance of 80 m from a level with the bubble at its centre is 1.31 m. When the bubble is moved by 5 divisions out of the centre, the reading is 1.39 m. The angular value of the one division of the bubble, is
A. 28.8 secs
B. 41.25 secs
C. 14.52 secs
D. 25.05
E. none of these
Answer: B
263. Locating the position of a plane table station with reference to three known points, is known as
A. intersection method
B. radiation method
C. resection method
D. three point problem.
Answer: D
264. If D is the degree of the curve of radius R, the exact length of its specified chord, is
A. radius of the curve x sine of half the degree
B. diameter of the curve x sine of half the degree
C. diameter of the curve x cosine of half the degree
D. diameter of the curve x tangent of half the degree.
Answer: B
265. If the chain line which runs along N-S direction is horizontal and the ground in E-W direction is sloping
A. it is possible to set offsets correctly on east side
B. it is possible to set offsets correctly on east side
C. it is not possible to set offsets correctly on west side
D. it is possible to set offsets correctly on both sides.
Answer: D
266. In geodetic surveys higher accuracy is achieved, if
A. curvature of the earth surface is ignored
B. curvature of the earth surface is taken into account
C. angles between the curved lines are treated as plane angles
D. none of these.
Answer: B
267. Determining the difference in elevation between two points on the surface of the earth, is known as
A. levelling
B. simple levelling
C. differential levelling
D. longitudinal levelling.
Answer: C
268. Contours of different elevations may cross each other only in the case of
A. an over hanging cliff
B. a vertical cliff
C. a saddle
D. an inclined plane.
Answer: A
269. Pick up the correct statement from the following :
A. The directions of plumb lines suspended at different points in a survey are not strictly parallel
B. In surveys of small extent, the effect of curvature may be ignored and the level surface of the earth is assumed as horizontal
C. In surveys of large extent, the effect of curvature of the earth must be considered
D. All the above.
Answer: D
270. The radius of a simple circular curve is 300 m and length of its specified chord is 30 m. The degree of the curve is
A. 5.73°
B. 5.37°
C. 3.57°
D. 3.75°.
Answer: A
271. During levelling if back sight is more than foresight
A. The forward staff is at lower point
B. The back staff is at lower point
C. The difference in level, cannot be ascertained.
D. none of these.
Answer: B
272. Two contour lines, having the same elevation
A. cannot cross each other
B. can cross each other
C. cannot unite together
D. can unite together.
Answer: D
273. The representation of general topography of a very flat terrain is possible only
A. by drawing contours at large interval
B. by drawing contours at small interval
C. by giving spot levels at large interval
D. by giving spot levels to salient features at close interval.
Answer: D
274. The bearing of line AB is 152° 30′ and angle ABC measured clockwise is 124° 28′. The bearing of BC is
A. 27° 52′
B. 96° 58′
C. 148° 08′
D. 186° 58′
Answer: B
275. A transit is oriented by setting its vernier A to read the back azimuth of the preceding line. A back sight on the preceding transit station taken and transit is rotated about its vertical axis. The vernier A reads
A. azimuth of the forward line
B. bearing of the. forward line
C. back bearing of the forward line
D. equal to 360°-azimuth of the forward line.
Answer: A
276. The surface of zero elevation around the earth, which is slightly irregular and curved, is known as
A. mean sea level
B. geoid surface
C. level surface
D. horizontal surface.
Answer: B
277. While working on a plane table, the correct rule is :
A. Draw continuous lines from all instrument stations
B. Draw short rays sufficient to contain the points sought
C. Intersection should be obtained by actually drawing second rays
D. Take maximum number of sights as possible from each station to distant objects.
Answer: B
278. Pick up the correct statement from the following
A. the contour lines having the same elevation cannot unite and continue as one line
B. a contour can not end abruptly, but must ultimately close itself not necessarily within the limits of map.
C. the direction of steepest slope at a point on a contour is at right angles to the contour
D. all the above.
Answer: D
279. In case of a double line river, contours are
A. stopped at the banks of the river
B. stopped at the edge of the river
C. drawn across the water
D. drawn by parabolic curves having their vertex at the centre of the water.
Answer: B
280. In case of a direct vernier scale
A. graduations increase in opposite direction in which graduations of the main scale increase
B. smallest division is longer than smallest division of the main scale
C. graduations increase in the same direction in which graduations of the main scale increase
D. none of these.
Answer: C
281. Correction per chain length of 100 links along a slope of α radians, is
A. 100 α2
B. 100 α
C. 100 α3
D. 100 α-1.
Answer: B